BQCXZ - ALUMINUM PUTTY (F) RESIN

  • MSDS: BQCXZ
  • Manufacturer: DEVCON CORP
  • Product Name: ALUMINUM PUTTY (F) RESIN
  • National Stock Number: 8030-01-206-2359
Product Identification

Product ID:ALUMINUM PUTTY (F) RESIN
MSDS Date:02/19/1988
FSC:8030
NIIN:01-206-2359
MSDS Number: BQCXZ

Responsible Party
DEVCON CORPORATION
30 ENDICOTT STREET
DANVERS, MA 01923
US

Emergency Phone: 508-777-1100

Info Phone: 508-777-1100

Cage: 16059

Contractor
DEVCON CORP
DANVERS, MA 01923-3753 US

Telephone: 1-508-777-1100

Cage: 16059

Ingredients

BISPHENOL A DIGLYCIDYL ETHER RESIN (MODERATE SKIN

CAS: 25068-38-6

Fraction By Weight: 10-30%

Hazards

LD50 LC50 Mixture:ORAL LD50 RAT: 11.4 G/KG (EPOXY RESIN)
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYES: MILD IRRITATION. METAL FILLER
PARTICLES COULD SCRATCH CORNEA. SKIN: MINIMAL TO MILD IRRITATION IN
MOST PEOPLE. INHALATION: UNLIKELY. NO DATA ON SYMPTOMS FOUND.
INGESTION: ALL INGREDIENTS ARE OF LOW ACUTE ORAL TOXICITY. NO DATA
FOUND ON SPECIFIC SYMPTOMS. APPROXIMATLEY 1% OF WORKERS MAY BECOME
SENSITIZED BY TOO
Explanation of Carcinogenicity:NONE
Effects of Overexposure:MUCH SKIN CONTACT WITH EPOXY RESINS; ITCHING,
SWELLING, OR RASHES MAY THEN RESULT FROM FURTHER CONTACT.
Medical Cond Aggravated by Exposure:ALLERGIES, ECZEMA, AND OTHER SKIN
DISORDERS.

First Aid

First Aid:EYES: FLUSH EYE WITH CLEAN WATER FOR AT LEAST 15 MINUTES
WHILE GENTLY HOLDING EYELIDS OPEN. GET MEDICAL ATTENTION. SKIN:
WASH THOROUGHLY WITH SOAP AND WARM WATER. CONSULT A PHYSICIAN IF
IRRITATION DEV ELOPS. INHALATION: REMOVE PATIENT TO FRESH AIR.
ADMINISTER OXYGEN IF BREATHING IS DIFFICULT. GET MEDICAL ATTENTION.
INGESTION: DO NOT INDUCE VOMITING. DILUTE WITH TWO GLASSES OF WATER
& GET MED AID.

Fire Fighting

Flash Point Method:PMCC
Flash Point:>400F,>204C
Extinguishing Media:CO2, DRY CHEMICAL, FOAM
Fire Fighting Procedures:FIREFIGHTERS SHOULD WEAR SELF-CONTAINED
BREATHING APPARATUS AND PROTECTIVE CLOTHING.
Unusual Fire/Explosion Hazard:NONE

Accidental Release

Spill Release Procedures:PREVENT SKIN CONTACT. SCRAPE UP AND DISCARD IN
SUITABLE CONTAINERS, USING INERT ABSORBENT MATERIAL SUCH AS
VERMICULITE IF NEEDED. WASH SPILL AREA WITH AN INDUSTRIAL CLEANING
AGENT. IF SOLVENT IS USED, TAKE CARE AGAINST OVEREXPOSURE & FIRE.

Handling

Handling and Storage Precautions:STORE CLOSED IN A COOL, DRY PLACE.
AFTER MIXING W/HARDENER, OBSERVE PRECAUTIONS RECOMMENDED FOR
HARDENER. AFTER PROPER CURING PRODUCT NOT HAZARDOUS.
Other Precautions:LEATHER ARTICLES (SHOES/BELTS) CANNOT BE
DECONTAMINATED, SHOULD BE DISCARDED. WHEN SANDING OR MACHINING
CURED MATERIAL, TAKE PROPER PRECAUTION AGAINST INHALATION OR DUSTS
GENERATED. THESE MAY INCLUDE ALUMINUM, (OBSERVE TLV OF 10 MG/M3).

Exposure Controls

Respiratory Protection:NONE REQUIRED AT NORMAL HANDLING TEMPERATURES.
Ventilation:LOCAL EXHAUST IS RECOMMENDED FOR CONFINED AREAS. GENERAL
MECHANICAL VENTILATION ADEQUATE FOR NORMAL USE.
Protective Gloves:CHEMICAL RESISTANT RUBBER GLOVES
Eye Protection:SAFETY GLASSES WITH SIDE SHIELDS
Other Protective Equipment:CHEMICAL RESISTANT RUBBER GLOVES AND OTHER
PROTECTIVE GEAR AS REQUIRED TO PREVENT SKIN CONTACT.
Work Hygienic Practices:REMOVE & CLEAN CONTAM CLOTHES & PROTECTIVE GEAR
BEFORE REUSE. WASH THOROUGHLY AFTER USING ESPECIALLY EATING &
SMOKING.
Supplemental Safety and Health

Chemical Properties

HCC:T6
Vapor Pres:NIL @ 78F
Vapor Density:>1
Spec Gravity:1.92
pH:7.0
Evaporation Rate & Reference:<<1 (BU AC=1)
Solubility in Water:NIL
Appearance and Odor:DARK GRAY PASTE WITH LITTLE ODOR

Stability

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS, BASES AND OXIDIZERS
Stability Condition to Avoid:OPEN FLAME AND EXTREME HEAT
Hazardous Decomposition Products:OXIDES OF CARBON, ALDEHYDES AND ACIDS
FROM INCOMPLETE COMBUSTION.
Conditions to Avoid Polymerization:HEAT IS RELEASED WHEN THIS RESIN IS
MIXED WITH EPOXY HARDENER. USE CAUTION WHEN MIXING A POUND OR MORE.

Disposal

Waste Disposal Methods:THE RESIN CONTAINS NO RCRA OR CERCLA LISTED
HAZARDOUS WASTES. DISPOSE OF IN ACCORDANCE WITH APPLICABLE STATE
AND LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.